A Shark That Eats Wood
 
  NEW
  HOME
  INPUT
  NEWSLETTER
  FORUM
  STORE

 

John's Tool Crib
by John Cupp

Press Release


A Shark That Eats Wood

In my search for high quality products to be used in boat building, I found the answer to the handsaw dilemma. I heard of a saw that you could bend against the surface of wood, and it would cut the end of the dowel flush against the wood without harming the wood surface. So I ordered one of them and another interesting saw made by Shark Corp, the same manufacturer. When they arrived, I tested them immediately against all of the pull and push saws I use for trim work and cutting. They produced a very thin kerf and cut like demons into any type of wood and even plastic PVC pipe. Inside the shipment was a small catalog with a wide selection of saws and other building implements. I had to write about these super sharp building implements to let our community know of them.

I emailed the company, and a day later the owner of the company, Mr. Nakayama, called me personally. I found out that Mr. Nakayama actually quality checks the saw teeth to make sure they are razor sharp. Any necessary corrections to the teeth are manually adjusted by him. I asked for a sample from his many products to review, and he gladly sent them to me to test.

A small number of days passed before the UPS man delivered the samples to my door. In the long box I found an assortment of the finest saws (instruments) on the face of the planet.

I found the extremely sharp 10-2440 saw, shown here.


cross tpi-17 rip tpi-9 blade length-9 ½”

Also in the box was the extremely thin and sharp 10-2410 with a kerf of only 0.004”. for super smooth fine cuts. It has a rib to support its ultra thin blade.


cross tpi-19 blade-10 5/8”

Along with that fine saw was a #21-2220 pry bar/nail puller. It has an exquisitely thin flat pry section that can fit behind the thinnest battens or trim and release them without a scratch.

It can also pull the most stubborn nails - even nails set with a nail gun! This style pry bar comes in two sizes, an 8” like I received and a 10” version. They also make a large assortment of strictly nail pullers from 6 ¼” to 14 1/8” that are the best I have ever seen.

They have duck head hammers with fascinating characteristics. There is a cat’s paw claws like a nail puller and highbrow rocker design. They also have a built in nail set, three striking surfaces that can side strike or strike with the elongated head to keep the nail penetrating after the first point of impact. Common hammers have a very small sweet spot but the Shark Duck Head Hammer uses the entire head as the sweet spot making nail driving a sheer pleasure. They come in three sizes with or without a milled head (shown is the smallest version).

They even make yard tools that still have the same custom made quality that all of Shark Corp. tools have.

I see I have gone off track again! Back to the contents of the shipped box. Now comes the best part. In the same box were the Takumi tools.

“TAKUMI” is the name given to only the master craftsmen in ancient Japan to honor their superior work.

These instruments are named after the fine craftsmen who built huge and elaborate castles and shrines using no nails. They used mortises, tongue and groove joinery, wooden dowels and wedges to build these national monuments. After centuries of use, these same monuments are still standing. The foundation of this carpentry work was the pull saw. Since the Empire is a series of Islands, the Japanese built rowing and sailing craft. The finish of these craft is legendary. All of this was made possible by the invention of the pull saw, the same type of saw being sold under the “TAKUMI” name.

These saws are the premium line of Shark Saws. I used the standard saws that came in the box until I knew how to cut with these different types of saws. It requires long even strokes without forcing or jerking. The “TAKUMI” saws have even finer blades that are hollow ground from front to back and across the saw.

You must remember that fine craftsmen have been forging this special steel for centuries, and building a fine saw such as the “TAKUMI” must be done by a trained skilled artist. The steel is hammered, then rolled over upon itself hundreds of times until it becomes perfect. This is the same type of steel used in the famous “SAMURAI SWORDS”.

I was so impressed when I took the first saw from its package; it was the RYOBA model 10-2710.


cross tpi-20 rip-graduated. blade length-81/4”
overall-22” kerf-0.020

From the tightly wrapped bamboo skin handle to the ultra sharp impulse hardened steel teeth, I knew this was a saw of unequaled performance. When I first cut into the Red Oak it felt wonderful because you don’t bear down. You just let the saw glide through the wood at an extremely fast rate. It was as if I were cutting butter and the cut itself needed no sanding; it was that smooth. I then used the other side of the saw to rip cut the same Red Oak. From that moment on, I knew these Takumi saws would have their own section in my tool crib alongside my finest measuring tools, because they were far and above everyday common tools.

The next saw was the DOZUKI super fine crosscut saw with 26 tpi and a kerf of only .015 . It is the finest most delicate saw of the “TAKUMI” saw line.


cross tpi-26 blade length-9” overall length-23 ¾”
super fine kerf-0.015”

It also uses a rib to help keep the ultra thin hollow ground blade from bending. It can be used for the most precise work any craftsman can do. I have cut an ultra thin slice from red oak that you could actually see through. I showed my wife and she was amazed! It will cut dovetails and mortising far superior to any machine cut. I find when I mark a pencil line on the wood, I can actually split that line with this instrument. It also cuts effortlessly through any type of hardwood. I have never used a finer saw.

I also have an AZEBIKI saw from the “TAKUMI” line. This strange looking saw is for cutting a hole inside a panel without starting from the outside.


cross tpi-15 rip tpi-9 blade length-3 ½”
overall length-17 ½” kerf-0.043”

Like all the other saws in this line it is ultra sharp. How sharp is ultra sharp? Well it is sharper than a fart and a fart can cut through clothes without making a hole! All kidding aside, the saws I have tested have no peers. The AZEBIKI saw performed better than I anticipated and I mastered starting the hole with this saw in no time at all. It has a crosscut side and a ripcut side on the extended blade.

One thing I must say is that these saws are so well balanced that they seem to become part of your arm and hand. The feeling is so natural that after using them you come to expect it from other tools, but they fail to give that same feeling. I wish I had discovered these saws when I was 20 instead of now. All the houses and boats I have built would have been much easier with these saws. Now that I am fifty-one and have a bad back, I can see that I am too soon old and too late smart.

Another saw in the “TAKUMI” lineup is the Kataba, a general carpentry saw with crosscut pattern teeth at 17tpi. It is designed for fast cutting through plywood, particleboard and dimensional lumber. With its ultra fine kerf and fast cutting ability, it could replace a power saw if noise were a concern. It is not meant for fine cutting like dovetails or delicate finish work.


cross-17 tpi blade length12”
overall length-25 ½” kerf-0.039”

The next two “TAKUMI” saws are RYOBA stilled saws which means they have two sets of teeth, cross cutting and ripping teeth.

The first is the10-2720.


cross-17 tpi rip-graduated blade length-9”
overall length-23” kerf-0.025

The next saw is the 10-2730 and the blades get larger and have courser teeth as the number grows. Some day I will have a whole set of these wonderful master craftsman built saws.


Cross: 10 tpi rip-graduated; Blade Length: 10 ¼”;
Overall Length: 23 ¾” Kerf: 0.015”

The last saw in this series is made to cut off dowels completely flush with the surface of the wood the dowel is placed in. The teeth have no set to scratch the surface of the wood but the saw slices right through the dowel wood. With its special spring steel the saw is bent to make the cut like a bow. No finer steel can be found in the world than is in these saws. This saw is the KUGIHIKI #10-2810 and should not be used for cutting thick material.


Cross: 24 tpi; Blade length: 6 ¾” Kerf: 0.014

Now you have seen the finest saws made. I urge you all to find a place in your toolbox to put one of these exceptional saws.

Shark Corp. makes all types of products and each is made with the finest materials. May I suggest buying the smaller inexpensive specialty saw like its “TAKUMI” cousins. This saw is the Dowel/Dovetail/Detail Saw #10-2204


cross 26 tpi blade length -6 ½”

I bought this saw on amazon.com, and it got me interested in these fine saws. Now hopefully Chuck will be able to sell them in his online store. My only wish is that Shark Corp. would make a line of chisels to match their super high quality traditional saws.

From John’s tool crib straight to you,

John