Here are some photos from the recent Fern Ridge lake messabout,
Near Eugene (example above):
The next messabout will be June 21-22, behind Caterpillar Island
(Fishermen's Slough, IIRC) on the Columbia near Vancouver Lake.
Check the Western Oregon Messabout mailing list for details:
People say that life is the thing, but I prefer reading.
<Logan Pearsall Smith>
The Web Page for the Fall Lake
Jordan Messabout is complete enough to post a link to. I hope
this helps all who are needing info.
here for messabout
Let me know if there is any info that I have left off that would
A Bolger Sneakeasy, Champlain, Micro and over a dozen amateur
built boats will be at this year's largest Amateur Boating Messabout
in the Northeast. 2003's première Messabout will be held
in Kingston, Ontario, Canada on the weekend of September 5-7,
2003. Visit https://www.brucesboats.com
and click on the Messabout map on the home page to peruse all
Chuck Leinweber of Duckworks eZine will be there, driving all
the way from Texas to do so. So we won't accept distance as being
an excuse not to come yourselves. Kingston, halfway between Toronto
and Montreal, is only 90 minutes north of Syracuse New York via
Interstate 81 and driving access is easy, involving only one turn
after you exit the freeway.
Kingston Messabout will be on a major waterway, permitting larger
amateur built boats to attend. The venue, Rideau Acres Campground
is on the Rideau Canal, which is linked to the St. Lawrence Seaway
and the world.
Rideau Acres Campground is a full service site, with a beach for
launching small craft, a ramp for trailer launches and 4 foot
draft docks for over twenty boats of all sizes. Serviced campsites,
RV sites are directly adjacent to the Messabout beach. The site
also has a large well equipped clubhouse, heated pool, real toilets
and hot water showers.
those who prefer a tad more luxury Kingston is well stocked with
hotels and motels, even a floating B&B on an ex-Canadian Coast
Guard Icebreaker! With the event taking place after Labor Day,
many will be offering rooms at off season rates.
Events at the Kingston Messabout will include a wine and cheese
"Meet and Greet" on Friday night.
The main Messabout will be on the Saturday from 10 a.m. until
4 p.m. On the beach, adjacent to the Messabout there will be a
"Boat Jumble" where boating items will be available
for swap or purchase on Saturday, all participants are invited
to bring whatever boat plans, outboards, and general boaty stuff
they want to unload. A "Potluck" dinner begins Saturday
evening at 6 p. m. and all participants are encourage to bring
a pail of their favorite slop to share. Salads, main courses,
stews, pastas, and desert items will be devoured by a crew of
At 10 a.m. Sunday morning I'll offer up a huge pot of my sugarless
"Texas Beans and Bacon" for a complimentary Cowboy breakfast
on the beach. Feel free to add to the feast with your favorite
early morning treats. Coffee, of course, will be most welcome.
Unscheduled Messingabout continues as desired on Sunday. Keep
in mind many of us work Saturdays and can only attend on Sunday,
so stick around as your schedule permits.
Anyone planning on attending with a boat is asked to contact me
by email at firstname.lastname@example.org or to call 1-888-214-9104
so I can add them to the database of visiting vessels on the Messabout
website. A ton of photos and a write up on the event will be sent
off to Bob Hicks at Messing About In Boats after the event. I
hope to meet lots of new "boat nut" friends at the Kingston
Amateur Messabout on September 5-7, 2003. Be there!
Messabout -Quinn's Cove Solstice, June 21, 2003
Here is a web site for our messabout. Lon
a note on our homemade harpoon for use shark fishing (only Mako's
- we won't kill any other kind of shark). We did this out of necessity,
as I really don't want to gaff a leaping fish with teeth. Also,
our twins are due soon, and didn't want to spend 200 bucks on
a harpoon for Mako's, so we made our own. Tolman Skiffs look fishy,
more so with a harpoon.
I made the first of two harpoons yesterday. I used an old telescoping
boat hook aluminum pole (two sections - when I figure out the
optimum length, I'll epoxy them together). The boat hook part
was long gone. So I used that end and carved out a 6 inch piece
of Doug fir with a power planer to fit into the end snugly. I
epoxied it in with some quick set epoxy. When it dried, I cut
it off flush, and drilled for a 3 foot section of steel rod I
got at Home depot for $3. I cut it in half to make two pieces
for two harpoons, since I got two bronze harpoon heads (unsharpened)
from Blue Ocean Tackle www.blueoceantackle.com
$20 plus 4 for shipping). After the wood was epoxied, I drilled
it out about 3 inches to take the rod, and epoxied that in, and
used the excess epoxy to wrap nylon twine around the business
end of the alum pole to make it stronger. Not necessary, but did
it anyway. While that dried, I sharpened he dart, since they come
unsharpened. Bronze sharpens up real easy with a file. I didn't
think it was going to be sharp enough but it's plenty sharp. Don't
ask me how I know. I had a short file. Its sharp!
I also cut off the wimpy looking 1/16th wire attached to the
dart and used 7 feet of 3/16th cable and crimped it onto the dart,
and used a thimble for the other end. The cable is 400lb working
load, so breaking strength is much higher.
The dart fits in the steel shaft rod pretty well, but one time
around with black tape made it nice and snug, but still easy to
come off after the dart goes thru a fish... then I taped the wire
to the shaft in a few places. To the thimble end, I just clip
my running line with a SS shackle and the line and off we go.
In the interest of thriftiness, I am using heavy duty detergent
bottles for the floats. Or I can use the anchor float (boat bumpers).
I think 100 ft of line is plenty, but read some guys use like
400-600' of lead core sinking line... But we are using ours as
a fly gaff substitute. I could always clip on the anchor line
to the end and if I needed more line. But for a normal size fish,
Less than 200 lbs say, I think we'll be fine. If we ever happened
hook a big fish, in excess of 300 - 400 lbs or something, we'll
have to stick two harpoons in him and shoot him to boot. There
are only three of us aboard. We intend to stick the fish with
the dart, and drive it right thru the fish. It is not for throwing.
It was fun to make, and every kid in the neighborhood wants to
see the harpoon...
Total cost was about $16 bucks each. I have another to make yet.
I guess I have lost my amateur status; This page
shows me working for money on the Schooner Virginia (see picture
#5 in the slide show:
Here is a webcam:
It's like paying a kid to go to Disneyland everyday.
Come on down!
The second Lake Charles Messabout will be on August 2, 2003 at
the Lake Charles Yacht Club under the bridge on Lake Charles in
Louisiana. The club features a launch area, sandy beaches, piers,
a clubhouse with restrooms and showers, shady areas and good companionship.
Activities: No scheduled activities but a lunch of hot dogs and
chili will be served at about noon and an informal dinner will
be served in the evening. The dinner is a Club function and was
scheduled on this date in conjunction with the Messabout. Happy
hour will start at about 6:00 pm with dinner following. Menu is
unknown but the Bonneys always have good food!
Who is invited? Anyone interested in ''Messing About in Boats''.
(This includes Club members.)
The grounds can be used for camping if you like and some slips
are available. I suggest that participants start arriving about
mid-morning but anytime is fine. If you plane to arrive early,
or Friday, let me know and I'll arrange to have the gate opened.
What is a messaabout? It is just a gathering of people interested
in small boats, either paddle, oar, power or sail. It generally
brings out home built boats but Potters, Montgomerys, Ventures,
etc. are all welcome. I'll probably have my PocketCat 18 and an
Uncle John 10 in the water.
For additional information contact me, Ken Abrahams at email@example.com
I put up a few pictues I took at the Duckworks Messabout
on S. Padre Island (Corpus Christi) on May 17, 2003.
It was a fine day, good fellowship, good sailing.
Gerard Mittelstaedt firstname.lastname@example.org
|PROGRESSIVE EPOXY INTRODUCES QUICK FIX 2300 - NEXT GENERATION,
"5 MINUTE," NON-HAZMAT, UNDERWATER EPOXY PUTTY
Progressive Epoxy Polymers, Inc. (Pittsfield, NH) has introduced
QUICK FIX 2300, a fast setting, Kevlar (tm) filled, epoxy gel/putty.
Quick Fix is considered a 'next generation' 5 MINUTE EPOXY. Actual
potlife is 5 to 15 minutes and the epoxy is hard in 20-35 minutes.
Simply mix the black part A resin with the white non hazmat (can
be shipped without regulation) part B in a 1 to 1 mix ratio and
apply with a putty knife or spreader. It can even be applied underwater.
The resulting hard epoxy is sandable. Private labeling is available.
PRICING: $98 gallon, $62 per 2 quart unit. Applications: filling,
fairing, gluing, waterproofing.
Progressive Epoxy Polymers, Inc. maintains an extensive website
of technical articles, information and links in addition to product
information. Progressive Epoxy has three on-site catalogs (marine,
industrial/commercial, and international) and offers a wide range
of overlapping underwater and dry surface coating products and
fillers from multiple formulators and manufacturers.
PAUL OMAN ----- Progressive Epoxy Polymers, Inc.
Frog Pond Hollow - 48 Wildwood Dr - Pittsfield NH 03263
603-435-7199 FAX 603-435-7182 VISA/MC/Discover